The Pi-Connect Lite is a HAT addon board for the Raspberry Pi 2B/3B/4/Zero(2,W) that allows easy and reliable interfacing with popular flight controllers used in unmanned vehicles.
It removes the complexity and risk of wiring up the telemetry and power connectors between the Pi and the vehicle systems.
It has been designed with reliability and a small form factor at the forefront, allowing for it to be used in both the smallest and largest of vehicles.
The Pi-Connect features:
The board also features a power switch which safely switches off the Pi via issuing a shutdown signal. This ensures the Pi is cleanly shutdown and reduces the risk of system corruption.
The Pi-Connect requires the following equipment:
Specification | Value | Notes |
---|---|---|
Operating Temperature | -25° - 70° C |
The Pi-Connect Lite is compliant with the following standards:
Specification | Value | Notes |
---|---|---|
Absolute maximum input voltage | 30V | Exceeding this voltage may damage the Pi-Connect |
Maximum input voltage | 7V | The Pi-Connect may work below this input voltage, but it is not guaranteed |
Output voltage variation (Vpp) | 0.35V | Variation is larger at higher input voltages |
Efficiency (30V input) | >84% | |
Efficiency (18V input) | >90% | |
Power dissipated (max) | 2.5W |
The power supply is based on the TPS54360 (or TPS54360B in Version 1.2+) DC/DC converter.
The Pi-Connect's power input needs to be soldered to the appropriate power source. The cables can be either soldered directly to the board, or the Power Cable Set can be soldered for a removable cable.
Next the board should be mounted onto the Pi's 40-pin connector such that the telemetry and power connectors face towards the interior of the Pi.
The telemetry connector should be connected to the flight controller. The pinout of the JST-GH connector allows for direct connection to the flight controller without any crossover cables required.
Some configuration is required to configure the power switch actions and serial port.
A reboot will be required for the changes to take effect.
/boot/firmware/config.txt
, not /boot/config.txt
Insert the following text into /boot/config.txt:
# Power switch dtoverlay=gpio-shutdown dtoverlay=gpio-poweroff
Then run the following command to enable the serial port if not running on a Pi 5:
sudo raspi-config nonint do_serial 2
On a Pi 5, instead insert the following text into /boot/formware/config.txt:
dtparam=uart0=on
To enable the additional UART(4) on the Pi4, insert the following text into /boot/config.txt:
dtoverlay=uart4,ctsrts
To enable the additional UART(4) on the Pi5, insert the following text into /boot/firmware/config.txt:
dtoverlay=uart3-pi5,ctsrts
In /boot/firmware/syscfg.txt, modify the line dtparam=i2c_arm=on
to dtparam=i2c_arm=off
.
Insert the following text into /boot/firmware/usercfg.txt:
# Power switch dtoverlay=gpio-shutdown dtoverlay=gpio-poweroff
In /boot/firmware/config.txt, modify the line dtparam=i2c_arm=on
to dtparam=i2c_arm=off
.
Insert the following text into /boot/firmware/config.txt:
# Power switch dtoverlay=gpio-shutdown dtoverlay=gpio-poweroff
The power switch performs a safe software shutdown of the Raspberry Pi before cutting power. The switch can be internal (the default, on board) or external (off board).
Fitting an external switch is useful in cases where the Pi-Connect is mounted in a difficult-to-reach location. A switch can instead to mounted in a better location and then wired to the external switch port on the Pi-Connect Lite.
If an external power switch is desired, ensure the switch is connected to the Ext Switch ports on the
Pi-Connect Lite board and the Int|Ext
trace is cut on the Int side and soldered on the Ext side.
The switch must be of a latching type with the centre pin common, like these switches.
To restore the functionality of the internal switch, restore the cut/solder of the Int|Ext
to the original state.
By default, the power switch uses GPIO3. As I2C also uses this port, there is a conflict.
On the Pi-Connect Lite V1.3 (or later), this can be resolved by moving the power switch to use GPIO4. This can be achieved by changing the GP3|GP4
jumper on the Pi-Connect Lite. The trace should be cut on the GP3
side and soldered on the GP4
side, as shown below.
Then, change the dtoverlay=gpio-shutdown
line to dtoverlay=gpio-shutdown,gpio_pin=4
in /boot/config.txt (or /boot/firmware/usercfg.txt or /boot/firmware/config.txt in Ubuntu)
If GPIO3 is preferred, reverse the jumper and software configuration changes back to defaults.
In the Raspberry Pi OS, the UART is identified as /dev/serial0
, or /dev/ttyAMA0
on the Pi 5:
Pin 1 is on the left-hand side when looking at the top of the board.
Pin | Function |
---|---|
1 | NC |
2 | Pi Rx |
3 | Pi Tx |
4 | NC |
5 | NC |
6 | Ground |
The additional UART(4) on the underside of the Pi-Connect Lite (V1.4+) is identified as /dev/ttyAMA*
(where *
is 1, 2 or 3) and has the following pinout:
The Pi-Connect uses the following Pins on the 40-pin header of the Raspberry Pi:
Pin | Alt Name | Function |
---|---|---|
2 | +5V | |
4 | +5V | |
5 | GPIO3 | Power Switch |
7 | GPIO4 | Power Switch (alt) |
8 | GPIO14 | Pi Serial Tx |
10 | GPIO15 | Pi Serial Rx |
19 | GPIO10 | UART4 CTS (Pi4 only) |
21 | GPIO9 | UART4 RX (Pi4 only) |
23 | GPIO11 | UART4 RTS (Pi4 only) |
24 | GPIO8 | UART4 TX (Pi4 only) |
27 | EEPROM | |
28 | EEPROM | |
37 | GPIO26 | Power Switch |
(This does not include the ground pins, all of which are connected to the Pi-Connect board)
The power port is a 2-pin Molex Nano-fit. The connector is Molex part number 1054301102 and corresponding plug is Molex part number 1053071202.
More information about the Nano-fit product family can be found at the Molex website.
Note that it is not necessary to install any additional software to get the Pi-Connect working.
The following packages are ready-to-go for new users or those who want a ready-made solution:
The following is a changelog of the hardware revisions of the Pi-Connect Lite. The revision numbers are printed on the top side of the board.
Issue | Affected Boards | Resolution |
---|---|---|
Power switch does not work after enabling I2C | V1.0 - V1.2 | Enable GPIO4 for power switch for V1.3+ (see I2C conflict section) |
External switch does not work when used with long cable | V1.0 | Add a 0.1uF capacitor between ground and GPIO3 |
The shutdown command sudo shutdown does not work | All | Use the physical switch on the Pi-Connect to shut down the Pi |